Nat single - top kwaliteit versterker met gm 70 eindbuizen
LeveringOphalen of Verzenden
|Type||:||Buis of Buizen|
VOEDINGSDEEL, IN EUROPA ( SERVIË ) ONTWORPEN EN GEASSEMBLEERD.
EEN UNIEKE BUIZEN-VERSTERKER VAN UITZONDERLIJK HOGE KWALITEIT.
2 jaar volledige garantie ( 6 maanden op de buizen )
Single Ended Integrated Amplifier
For the first time NAT has tried to introduce a real high-end component in a price region of entry level devices.
The NAT “Single” is a tube based integrated pure dual mono amplifier.
With an integrated amplifier, there is no need for an interconnect cable between preamplifier and power section – one
of the positive aspects of an integrated amplifier as a single unit.
“Single” operates in a single ended, zero feedback, pure class A manner. Power output is 50W into 8 ohms.
Recommendation for the best result is to have medium to flat loudspeakers impedance curve, from 4 ohms to 16 ohms.
The driver (input) stage contains special tubes (triode) capable to act as low distortion voltage amplification devices.
The Output stages are single military grade direct-heated triodes type GM70 being high performance devices capable
togive a peak dissipation of 125W .It is a truly single ended design without parallel connection of tubes, yet moderate
50W of output power.
A hand crafted wide bandwidth output transformer (custom designed for NAT ) is used in this unit.
The output transformer bandwidth is from 10Hz – 60.000Hz. That is an extremly good result for an integrated single-
ended amplifier, yet zero feedback design.
By a specific technical approach the output transformer in combination with power tubes type GM70 may drive easy
any type of standard loudspeaker.
Soft start improving reliability of entire integrated amplifier by avoiding voltage stress during turn-on procedure.
Standby function additionally improving mention reliability, keeps the amplifiers internal voltage at a minimum.
There is no need for any adjustment from time to time of output tubes standing current. The electronic circuit
automatically adjusts current through GM70 tube no matter of tube duration – which means a constant current in time
domain – from the brand new start to the end point of tube life.
To avoid unnecessary heat from pure high class A operation, ”Single” has the possibility by adaptive bias (select on
front panel) to choose lower mode - 15W of output power that reduces the power consumption significantly.
The power supply section also speaks for itself. Main 1.000w transformers (separate wound for each channel) are
custom designed for NAT “Single”, also works silently. For the purity of power supply voltage there are special
designed separate regulators also in zero feedback manner for all amplifier stages including the output one. In such a
way the sound quality is totally independent from line voltage instability.
The tubes (input triode drivers) are N.O.S. (new old stock) grade and have high reliability. “Single” is equipped with a
multi function remote control unit made from a solid block of aluminum. The front panel is made of a solid block of
aluminum and indicates the amplifiers functions with blue led displays.
Attenuation is based on relay (with gold plated contacts and silent operation) network that is computer controlled –
there are 100 positions of attenuation and there always is only one (single) high quality resistor on the signal path.
Quality of electronic material that is used inside “Single” : 0.1% Vishay resistors, electrolytic capacitors for 105 degrees
Celsiusof working temperature, last generation of industrial grade semiconductors, Teflon insulated connectors, a
special designed power transformer, N.O.S. input tubes, high reliability silent relays with gold plated contacts…
The amplifier works from 100 – 250 VAC, 50-60Hz (set in factory).Technical Specification:
Power 50 W @ 8 ohms
.Frequency Response10 to 60 kHz, -3 dB; 20Hz to 20kHz, +/-0,5dBNoise 90 dB
, IHF reference to 1WGain35 dB (X 55) Phase status: non-inverted (0 degree)
THD & N< 0.1 %
Input Impedance>15 kohms
Output Impedance:<1.6 ohms (damping factor >10 reference to 16ohms load @zero feedback)
Stereo Separation>95 dB @ 10 kHz.
Tube Complement 2 x 6N23P (E88CC) & 2 x GM70 per unit
Power Requirements100VAC to 240VAC (50 to 60 Hz), max. 370 VA.
Dimensions; 483 mm wide , 400 mm deep, 260 mm high.
NET Weight (Control Unit) approx. 51 kg. unpacked. TOTAL Weight approx. 66kg total with transport wooden box .
- single ended type - integrated amplifier
- zero feedback design
- triode direct-heated output type
- 50 W of pure class A
- full dual mono construction
- custom designed 1.000W encapsulated power transformer
- full stabilisation for all amplifier stages
- two tubes (NOS) for driver purposes
- separate toroidal transformer for digital control
- dot-matrix display (15 level of intensity with turn off light mode)
- remote control made from solid block of aluminium
- automatic bias
- adaptive bias (to control dissipation of the output stage)
- standby function
- relay (silent type) attenuation network
- all aluminium modulated chassis
- teflon isolated connectors
Kijk ook eens op de website van de fabrikant: www.nataudio.com
Op speciale bestelling leverbaar. Levertijd ca. 12 dagen. Vooruitbetaling van € 3500 door middel van overboeking naar onze bankrekening IBAN: NL61INGB0006743041 t.n.v. highendaudioimport B.V. te Meppel De resterende € 3450 graag contant te voldoen bij aflevering. In België en Nederland berekenen wij geen bezorgkosten. Overige landen op aanvraag.
De meerprijs voor de uitvoering met een nano crystalline core balanced input transformator is € 435.
De meerprijs voor de uitvoering met een nano crystalline core balanced full silver ofc wire wound balanced input transformator is € 890.
ZIE VOOR NADERE INFORMATIE ONZE WEBSITE/WEBSHOP: WWW.HIGHENDAUDIOIMPORT.NL