MOVING COIL CARTRIDGE

• Elliptical stylus chip and durable duralumin tapered pipe cantilever
• 10O mid impedance specifications
• Dramatically increased magnetism with neodymium magnets and PCOCC
• High separation, wide-response dual moving coil
• VC Mold eliminates unnecessary vibrations
• “Hanenite” anti-vibration rubber eliminates unwanted vibrations

AT33EVMOVING COIL CARTRIDGE
The original model of this stereo cartridge is the AT33ANV, which was available as a special release to celebrate our 45th anniversary. The A33ANV was the first in the AN33 series to feature a Duralumin cantilever, which received wide acclaim for its sound quality. Retaining the basic specification, we present a further improved and evolved model.
The A33EV is a ½ inch, standard mount 0.3 x 0.7 mil elliptical cartridge featuring a tapered Duralumin cantilever which reduces the effective mass of the cartridge, resulting in a more durable cantilever. The Dual Moving Coil cartridge design increases channel separation and extends the frequency response range delivering extraordinary audio quality. Internally constructed with a neodymium magnet enhances magnetic energy and PCOCC wire for pure audio transmission.

• Elliptical stylus chip and durable duralumin tapered pipe cantilever
• 10O mid impedance specifications
• Dramatically increased magnetism with neodymium magnets and PCOCC as the coil
• High separation, wide-response dual moving coil
• VC Mold eliminates unnecessary vibrations
• “Hanenite” anti-vibration rubber eliminates unwanted vibrations

“MINIMISES UNNECESSARY VIBRATION”
‘Hanenite’ is used in the housing interior and the cantilever fulcrum support to minimize unnecessary vibration, to allow the outstanding basic performance of the dual moving coil to fully express itself.“ABILITY TO RICHLY REPRODUCE SOUNDS”
Elliptical stylus chip, embedded into a hard duralumin tapered pipe cantilever, has the ability to richly reproduce sounds in the medium and low ranges. With its outstanding machine strength, the duralumin cantilever is tough enough for the job and produces natural sounds without distortion.
Type
Dual Moving Coil
Mounting
1/2″ Centers
Frequency Response
15 – 50,000Hz
Body Material
Aluminium/Synthetic Resin
Channel Separation
30dB (1kHz)
Output Channel Balance
0.5dB (1kHz)
Output Voltage
0.3mV (1kHz and 3.54cm/sec.)
Vertical Tracking Angle
23°
Vertical Tracking Force Range
1.8 – 2.2g (2.0g standard)
Stylus Shape
Elliptical
Stylus Curvature Radius
0.3 x 0.7 mil
Stylus Construction
Nude Square Shank
Cantilever
Duralumin
Coil Impedance
10Ω (1kHz)
Coil Inductance
22µH (1kHz)
DC Resistance
10Ω
Static Compliance
40×10-6cm/dyne
Dynamic Compliance
10×10-6cm/dyne (100Hz)
Terminal Pins
Brass
Recommended Load Impedance
More than 100Ω (when head amp connected)
Weight
6.9g
Dimensions
H16×W16.6×D26.5mm
Replacement Stylus
When the stylus is to be replaced, replace the entire cartridge. Take the used cartridge to your Audio-Technica Authorised Service Centre. The new cartridge, or any other model which is desired among the line-up of MC cartridges sold by Audio-Technica, are available at the stylus replacement price.
Accessories Included
Non-magnetic screwdriver × 1, Washer × 2, Protector × 1, Cartridge installation screws 13 mm × 2 and 19 mm × 2, Nut × 2, Brush × 1, PCOCC lead set × 1